northwest Repairing a bad coil lead, at the coil end.
Welcome, Guest. Please login or register.
Saturday March 25 2017 16:53:46 AEDT PM
Home Help Login Register
News: forum firewall bad behaviour Cloudflare Bot scout
Welcome to the Australianelectronicgoldprospectingforum founded in July 2010, an add free totally independent forum with over 70 boards and paid for and managed by the Admin.Total forum Topics:8,658 Total forum Posts:41,100 Members: 639 Total page views:7,742,442 Admin and  forum and domain name owner :marjen at optusnet.com.au. Guests can only see a limited number of boards at present and cannot see any links. Guest cannot post and never will be permitted too!Registration of new members must be approved by admin.Anyone known to have any past or present association with Codan/ML or acting on their behalf as a proxy or intermediary  will not have their registration approved. All  original Photos and posts and  original materials displayed on this site are COPYRIGHTED and remain the property of the poster and the australianelectronicgoldprospectingforum.com. All messages on this forum express the personal views of the author and should not be interpreted as necessarily being in accord with those of the forum owner and neither the owner of this forum and its domain name nor SMF or the forum software developers or the forum host shall be held responsible for the content of any message. Admin reserves the right to remove any offensive or objectionable posts. No defamatory material or politics/religion or issues of race will be permitted.
QED is here! ML have NOT stopped the QED!
Goldsearch Australia has been appointed the Australian Distributor for the QED. QED info on the Goldsearch website has been updated.
This is the only forum where you can talk directly with the designer/ manufacturer of the QED!
Jrbeatty and Reg Wilson  and  Yellowfin have NO vested  or pecuniary interests(or secret deals or cash for comment or any other undisclosed benefits )in the QED other than using it to find gold which it is doing very successfully!
Over the overwhelming majority of typical Gf ground the QED GB works just fine! Another new user has used his QED over "fairly difficult ground around Waanyarra and Kooyoora areas  " and not reported any GB problems!
The so called QED GB problem is just  more fake news created by  some fake, delusional and dishonest imbecile cretins on 1/2 wits (who is a proven forum hacker and liar and  just dumb!) pox, liars and abomination and disgraceful atrocity sewer rats "forum" that have never used a QED! The QED has been used successfully to detect under 300k steel tower transmission lines(try that with a gp/gpx  with a mono coil!!!) so it  can handle bad  EMI! The QED will also run quite and stable in a household with electrical appliances running.Try that with a ML with a mono coil!!! "QED matches and and in most cases outperforms the SDC"  and will thrash it for depth on bigger gold. QED sales are still strong so if you are on the waiting list please be patient as BW is working 12 hours a day to try and reduce the waiting time.
Except for the USB port the prototype QED's are identical in EVERY respect to the production models and according to the designer  the production models may even be  better!
4umer makes another liar a moderator! How low can 4umer go!

australian electronic gold prospecting forum.com  |  general detector and coil maintenance  |  Detector and coil maintenence  |  Topic: Repairing a bad coil lead, at the coil end. 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Repairing a bad coil lead, at the coil end.  (Read 3779 times)
Mechanic
regular members
Hero Member
***
Offline Offline

Posts: 936


« on: Friday September 17 2010 22:26:10 AEST PM »

Hi Guys,

Well my coil has still been giving me grief! Damn thing every time the lead is bumped near the coil I get a false noise. This is very annoying. Also sensitivity is down, I found a 0.09g speck using a 15X12" DD commander in mono and could barely hear the same speck with the 11"dd in mono!

So time to bite the bullet and pull the coil apart to cut the bad bit off the coil lead.

The detector sounds off when the lead is wriggled at the strain relief.


Use a good sturdy knife to cut/ break the glue that holds the coil shell together. Work all the way around the coil.


Once all the glue is broken, carefully separate the shell.



Now find the end of the tape around the edge of the coil and carefully remove. A small amount of heat may help to prevent tearing the shield paint off.


Use a hot air gun to remove the bottom shield as it is held on with hot melt glue.


Use a hot air gun to melt the glue and find the end of the coil lead. Do not get things too hot or the foam will melt! Unsolder the coil lead and take note of what wires go where. The wire for the receive coil is very fine so be careful.

Cut the coil lead an inch or so past where the strain relief grabbed the cable and re-solder to the coil windings again. Use only just enough solder. Seal the coil lead join up with hot melt glue back where it originally came from. Test the coil!

Now reassemble the coil. Reuse the tape from the side of the coil. You may need to use some masking tape to help hold it in place. Put the shield wire back where it was and use some conductive silver to guarantee a good connection between the shield wire and the shield paint.

Put some masking tape over the wire to hold it down. Wrap some masking tape around the edge of the coil. Add tape where necessary.

This is the coax for the receive coil and is also for the coil shield. It was completely broken.


This is the wire for the transmit coil. It was holding on by about 10 wires!


Use super glue to glue the coil shell back together. Make sure everything is nice and tight.

I hope this helps some of you take the leap and fix up your old coils. What have you got to loose? Just don't blame me if you do something wrong and hurt your detector!

Cheers Mick

Ps If you want to get rid of an old coil that doesn't work let me know.
Logged
peterlinktech
Guest
« Reply #1 on: Friday September 17 2010 23:18:26 AEST PM »

The strain relief cuts the cable like a knife, it is recommended to leave the strain relief loose so the cable lasts a long time.  It mainly happens to DD coils.
Logged
6666
Newbie

Offline Offline

Posts: 146


« Reply #2 on: Sunday May 1 2016 14:47:34 AEST PM »

Thanks for showing pictures of the repair, the shield looks like two pieces of paper painted with a graphite paint, then a piece of tape wrapped around the edge and painted with graphite   , when you reapplied the ground wire is it wrapped around the edge and glued down to both sides of the shield paper ?
Logged
Mechanic
regular members
Hero Member
***
Offline Offline

Posts: 936


« Reply #3 on: Sunday May 1 2016 15:54:56 AEST PM »

  
Thanks for showing pictures of the repair, the shield looks like two pieces of paper painted with a graphite paint, then a piece of tape wrapped around the edge and painted with graphite   , when you reapplied the ground wire is it wrapped around the edge and glued down to both sides of the shield paper ?

No, it isn't wrapped around the edge. It is joined to the junction where the shield of the coax connects to the winding, then comes to the top via the same hole the coax goes through, then about 10~15cm along the top toward/past the centre and then goes through the paper and coil to the bottom side of the coil. If it was done on the edge the coil would be prone to falsing when bumped along the edge.

Cheers Mick
Logged
Doug
Administrator
Revered Supreme Hero Member
*******
Online Online

Posts: 15332



« Reply #4 on: Sunday May 1 2016 16:28:51 AEST PM »

  
  
Thanks for showing pictures of the repair, the shield looks like two pieces of paper painted with a graphite paint, then a piece of tape wrapped around the edge and painted with graphite   , when you reapplied the ground wire is it wrapped around the edge and glued down to both sides of the shield paper ?

No, it isn't wrapped around the edge. It is joined to the junction where the shield of the coax connects to the winding, then comes to the top via the same hole the coax goes through, then about 10~15cm along the top toward/past the centre and then goes through the paper and coil to the bottom side of the coil. If it was done on the edge the coil would be prone to falsing when bumped along the edge.

Cheers Mick

Thanks mick! happy face
doug smile
Logged

All posts on this forum are the personal views of the author and should  not necessarily be  interpreted as those of Admin The QED contains NO patented or protected IP!!! No fake users on this site! This forum does not depend on  guest posting liars to survive!1/2 wit powerless to login and post! LO
6666
Newbie

Offline Offline

Posts: 146


« Reply #5 on: Sunday May 1 2016 16:46:29 AEST PM »

  
  
  
Thanks for showing pictures of the repair, the shield looks like two pieces of paper painted with a graphite paint, then a piece of tape wrapped around the edge and painted with graphite   , when you reapplied the ground wire is it wrapped around the edge and glued down to both sides of the shield paper ?

No, it isn't wrapped around the edge. It is joined to the junction where the shield of the coax connects to the winding, then comes to the top via the same hole the coax goes through, then about 10~15cm along the top toward/past the centre and then goes through the paper and coil to the bottom side of the coil. If it was done on the edge the coil would be prone to falsing when bumped along the edge.

Cheers Mick

Thanks mick! happy face
doug smile



Thanks Mick, its just the 8th picture down sorta looks like the ground wire is going around the edge and being glued, but apparently not, thanks.
Logged
Mechanic
regular members
Hero Member
***
Offline Offline

Posts: 936


« Reply #6 on: Sunday May 1 2016 17:48:17 AEST PM »

  
  
  
  
Thanks for showing pictures of the repair, the shield looks like two pieces of paper painted with a graphite paint, then a piece of tape wrapped around the edge and painted with graphite   , when you reapplied the ground wire is it wrapped around the edge and glued down to both sides of the shield paper ?

No, it isn't wrapped around the edge. It is joined to the junction where the shield of the coax connects to the winding, then comes to the top via the same hole the coax goes through, then about 10~15cm along the top toward/past the centre and then goes through the paper and coil to the bottom side of the coil. If it was done on the edge the coil would be prone to falsing when bumped along the edge.

Cheers Mick

Thanks mick! happy face
doug smile



Thanks Mick, its just the 8th picture down sorta looks like the ground wire is going around the edge and being glued, but apparently not, thanks.

Hmmm, looks like that is how that coil was done. But I think it is probably better to do it the way I described above.

Cheers Mick
Logged
Pages: [1] Go Up Print 
australian electronic gold prospecting forum.com  |  general detector and coil maintenance  |  Detector and coil maintenence  |  Topic: Repairing a bad coil lead, at the coil end. « previous next »
Jump to:  


Login with username, password and session length

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2006-2009, Simple Machines
Simple Audio Video Embedder

BisdakworldClassic design by JV PACO-IN
Valid XHTML 1.0! Valid CSS!